20 Trailblazers Lead The Way In Fix Door Hinge > 고객센터

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. However, if the screw holes are damaged and aren't able to hold screws, you may need to use dowels and wood glue before you can put back the hinge.

Before you do this, however, brush away surface rust. This will allow the dowels to remain in place and provide them a solid base to grip into.

Eliminating the Hinges

A lot of door hinges are removable, which makes it easier to move the door from one side to the other or to take the entire door off the frame if need be. The removal of the hinges is simple for anyone with patience, though you do need to know how do it right.

If the hinges are painted you will need to remove the paint prior to attempting to remove the pins. It is possible to scratch your door if do not remove the paint. Place the hinges in the stainless steel pot and fill it up with water to the point that the hinges are completely submerged. The hinges should remain in the pan for around 30 minutes. The heat from the water will soften the paint, making it easier to remove.

Once the pins have been loosened, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, but a magnetic screwdriver is recommended for this project. This type of screwdriver has been specifically designed to take out metal screws and will aid you in getting the job done much faster.

It is a good idea to spray some lubricant on the hinges prior to trying to remove them. A simple lubricant will help you to speed up the process and make the removal of screws and pins easier. You can find this kind of lubricant in most hardware and home improvement stores.

You should also keep in mind that the number of door repair hinge hinges you'll need will vary depending on the type of door and the setting. Heavier and solid-cored Bi-fold Doors hinges will require more hinges whereas lighter and hollow-cored doors may only need two or three.

Understanding the different types of hinges will help decide which one is the best for your particular situation. Exterior hinges are designed to support the weight of a door, whereas interior hinges must be able to support heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may loosen and begin to sag or hang crookedly. This can be a major issue, but the solution is usually easy. A simple retightening will usually solve the issue. If the screw holes have been stripped out, it may be difficult to fix. There is a method to make these holes back to their original size that uses a wood dowel.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Then, use wood glue and dowels made of wood to fill the hole. The dowel should be cut to a length that is similar to the screw to ensure a secure fit. Reinstall the screw and tighten it to the desired degree of tightness. If the window door repairs locks glass hinges continues to have the tendency to be bowed, then add another dowel to the gap and repeat the process. Be sure to shut the door slowly so that you can check the perimeter clearances after each adjustment.

Another option is to utilize an old-fashioned wood plug instead of a dowel. This will work similarly, but it may take a bit longer to install. You can insert the wood piece that has been whittled down to the right size. If you don't have a woodworking tool you could also make use of toothpicks or wooden matches.

Use a countersink to make the hole smaller for the head of screw after you have put it back in place. This will stop the screw from rubbing against the edges of the doors as they are opened and closed. This will make it easier to tighten the screws when reinstalling hinges.

After you have reinstalled the hinge, be sure to lubricate it with a dry lubricant to help keep it from getting stuck in the future. Products like PB Blaster or Liquid Wrench are excellent alternatives. Apply a thin layer of it and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few fixes. The first step is to check that the screws holding the hinge plate to the door frame are tight. If they're loose, tighten the screws using a power drill or screwdriver. Be careful not to tighten the screws to the point that they begin to cause gaps at the trim joints, or even worse cause threads to be stripped.

If the problem is that the hinge plates are separating from the jamb and door and jamb, you can fix them by applying wood glue to the back of the plates, and then inserting toothpicks or wooden dowels into the holes. The toothpicks and dowels provide a solid foundation for the screws, and prevent the plates from shifting as you drive them in. Allow the glue time to dry before reattaching your hinge.

The screws can also be stripped or missing. This problem can be fixed by replacing the screws. Be sure to use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the door after you have reattached your hinge and check the gap between the frame and the door. It should be about the thickness of a nickel all the way around or less if there's a gap created by a door that was not properly hung. If the hinges were set up properly, this shouldn't be a problem.

If the hinges still seem loose, you could add a stronger hinge between the hinge plate's surface and the mounting surface. This will allow the hinges more room. You can also try removing the hinge pin from the troublesome hinge tilt and turn window hinge covers pounding it down with a hammer in order to make it more secure or using the hinge pin from a different angle altogether. It is also possible to lubricate the hinges with mineral or jojoba oil to decrease friction and assist in keeping their position. Lubricating your hinges frequently will help keep them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The friction caused by a hinge's constant movement attracts dust particles. Without regular cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspection will preserve the quality and function of hinges on doors.

Inspect the hinges to see how much rust has formed on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you can save the hinges, begin by brushing away loose rust using steel wool and a wire brush. Then apply a rust remover from a commercial store or a homemade solution such as lemon juice to the hinge. Let the rust-removing solution remain on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you do not want to spend cost and time to replace your hinges, simply retightening the screws will bring back the hinge's functionality. It is possible to attach a wooden shim or dowel to the hinge if the screw holes have been degraded. Dowels made of wood are square pieces of wood that are in the form of rods, which are available in various lengths and sizes. You can buy them online, in woodworking supply stores and home improvement stores.

You can also create a shim from a piece either plastic or metal, depending on the kind of hinge you have. To make a dowel cut a piece of wood dowel or other sturdy material to the desired size. You can then dip the dowel into a carpenter's glue and insert it into the cut hole and let the glue hold the dowel in the right position.

Before cleaning the hinges put down a towel or cloth to protect your flooring from spills. After the area is secured then clean the hinges with a soft sponge or cloth coated with a mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices or tight areas.